Description
Two-Way Full Range Loudspeaker with 2 x 10" Differential Drive® LF
The VLA-C265 uses JBL proven technology components. The high frequency section is horn-loaded for maximum sensitivity and optimum pattern control and features three D2415 drivers featuring 1.5” diameter annular diaphragms, 1.5” voice coils, and neodymium motors.
The low-frequency section utilizes dual 2261 10” Differential Drive® 3” voice coil drivers.
Enclosures feature multi-layer reinforced fiberglass and steel end-panels. Grilles are zinc plated, powder coated 14-gauge perforated steel with an acoustically transparent black grill cloth backing, a hydrophobic mesh underlayer, and a waterproof rail system.
The rigging system is inherent to the design of the system. Inter-box angles are selected when the array is assembled. Other accessories include a rigging frame, pull-back bar, and a cardioid kit for the sub.
Features
- Compact line array module optimized for permanent install applications
- Advanced technology component transducers for low weight and high output
- Outdoor IP55 rated enclosure for protection from dust and water
- Comprehensive rigging points for creating a line array configuration
- Fiberglass box construction and weatherized components
- Can be bi-amplified for maximum SPL, or fed passively for reduced amplification costs
- 65° horizontal coverage pattern
Specifications
System
- Frequency Range (-10 dB) 85 Hz - 19 kHz
- Frequency Response (±3 dB) 108 Hz – 16.5 kHz
System Power Rating
- Full Range
- 800 W Continuous Pink Noise (3200 W peak), 2 hrs
- 400 W Continuous Pink Noise (1600W peak), 100 hrs
- Bi-amp LF
- 800 W Continuous Pink Noise (3200 W peak), 2 hrs
- 400 W Continuous Pink Noise (1600W peak), 100 hrs
- Bi-amp HF
- 150 W Continuous Pink Noise (600 W peak), 2 hrs
- 50 W Continuous Pink Noise (200 W peak), 100 hrs
Maximum Input Voltage
- Full-Range 80 V Rms (2 hrs), 160 V peak
- Bi-Amp LF 80 V Rms (2 hrs), 160 V peak
- Bi-Amp HF 50 V Rms (2 hrs), 135 V peak
- Maximum SPL (1m) 131 dB Cont. Ave (2 hrs), 137 dB Peak
Sensitivity
- Full-Range 102 dB (85 Hz – 19 kHz)
- Bi-Amp LF 100 dB (85 Hz – 950 Hz)
- Bi-Amp HF 108 dB (950 Hz – 19.2 kHz)
- Coverage Pattern (-6 dB)
- Horizontal: 65° (+15°/-10°, 1.5 kHz to 15 kHz)
- Vertical: Varies with array size and configuration
Impedance
- Full-Range 8Ω, 6.6Ω min @ 162 Hz
- Bi-Amp LF 8Ω, 6.8 Ω min @ 162 Hz
- Bi-Amp HF 16 Ω, 16.2 Ω min @ 11 kHz
- Amplifiers Crown DCi Family with DSP on-board
- Recommended:
- Crown DCi 2 | 1250N
- Crown DCi 4 | 1250N/ND/DA
- Crown DCi 2 | 2400N
- Crown DCi 4 | 2400N
Transducers
- Low Frequency Driver 2 x 2261FF, 254 mm (10 in) diameter, each with two 76 mm (3 in) diameter voice coils, Neodymium Differential Drive®, Direct Cooled™
- High Frequency Driver 3 x 2415K, D2 Dual Diaphragm Dual Voice Coil Compression Drivers, each with two 38 mm (1.5 in) dia. Voice Coils; 21 mm (0.8 in) exit
Physical
- Enclosure Material Fiberglass shell, gelcoat finish, with 18 mm Birch plywood internal bracing.
- Grille Powder coated 14 gauge hex-perforated steel with zinc under-coating, backed with acoustically transparent cloth and hydrophobic screen.
- Inter-Enclosure Angles
- VLA-C265 to VLA-C265: 1.5°, 2.4° 3.8°, 6.0°, 9.5° using VLA-C265 Bracket Plate (included with VLA-C265)
- VLA-C265 to VLA-C2100 (either model on top/bottom): 1.9°, 3.0° using VLA-C2100 Bracket Plate (included with VLA-C2100) and 4.7°, 7.5°, 11.9° using VLA-C265 Bracket Plate (included with VLA-C265)
- VLA-C265 below VLA-C125S Subwoofer (VLA-C265 cannot be connected above C125S): 0°, 5° using VLA-C125S Bracket Plate (included with VLA-C125S)
- Environmental IP-55 rating per IEC529 (dust protected and protected against jets of water).
- Terminals CE-compliant covered barrier strip terminals. Barrier terminals accept up to 5.2 sq mm (10 AWG) wire or max width 9mm (0.375 in) spade lugs. Touch-proof covers.
- Colors -GR: Gray (similar to Pantone 428C), -BK: Black
- Dimensions (H x W x D) 381 x 848 x 460 mm (15.0 x 33.4 x 18.1 in)
- Net Weight (ea) 37.7 kg (83 lbs)
- Shipping Weight (ea) 44.0 kg (97 lbs)
- Included Accessories
- 2 pcs. VLA-C265 Bracket Plates
- 8 pcs. M10 x 35 mm stainless steel bolts (1.5mm pitch, 6 mm hex-drive) for attaching Bracket Plates
- 2 pcs. Plastic Trim Cover Panels for Bracket Plates, each attaches via
- 4 pcs (8 total) 3-32 x ½” trusshead, phillips-drive, stainless steel bolts.
- Optional Accessories VLA-C-SB Suspension Bar Kit for the array, includes 2 identical Suspension Bars (for top/bottom), 4 pcs ¾-inch Class 2 Screw Pin Shackles (must use 2 Shackles for each Suspension Bar, located at end channels, not in the center).
