The AN-16/o v.4 Output Module connects to any Pro16 input module, console card, or A-Net distributor and provides 16 balanced TRS line-level analog outputs. Five output levels, from mic to +24dBu, are available to easily accommodate the level requirements of the gear its output signals are being connected to.
Use the AN-16/o v.4 anywhere analog outputs are required: on stage or at FOH in a digital snake, in the studio, for a recording split, or in even the most complex audio networks. Adding a digital split to a Pro16 system is as simple as connecting an additional AN-16/o v.4 Output Module.
Compatibility Note: AN-16/o v.4 Output Modules with serial numbers 51162 and lower are not compatible with the Pro16e A-Net output of the AN-16/i v.2 Input Module.
- 16 balanced mic- or line-level outputs
- Four-position output level switch per channel pair
- +24, +18, and +4dBu line-level, or mic-level outputs
- 48kHz, 24-bit D/A converters
- Unlimited splits and digital copies
The AN-16/o v.4 Output Module is a 1U rack-mount 16-channel digital-to-analog converter for Pro16® digital snake and audio distribution systems. Digital audio transmitted to the AN-16/o v.4 via Aviom's A-Net Pro16 digital audio transmission protocol is converted to analog using 24-bit, 48kHz converters.
Sixteen balanced outputs are provided on the rear panel via DB25 multipin connectors. The analog outputs can be set (per channel pair) to +24dBu, +18dBu, +4dBu, or mic level.
Connecting to Wireless In-Ear Monitors
In personal mixing systems using the A360 Personal Mixer with the D800 or D800-Dante A-Net Distributors, the AN-16/o v.4 simplifies connections to wireless IEM systems. Each A360 Personal Mixer sends its stereo mix output back into the network which appears as a pair of channels on the AN-16/o v.4. Each AN-16/o v.4 supports up to eight A360s. Simply patch the analog outputs on the AN-16/o v.4 into the IEM transmitter's inputs. No analog cables are required at the A360 on stage.
Digital Snakes and Audio Networks
Use the AN-16/o v.4 anywhere analog outputs are required: on stage or FOH in a digital snake, in the studio, for a recording split, or in even the most complex audio networks. Adding a digital split to a Pro16 system is as simple as connecting an additional AN-16/o v.4 Output Module.
The AN-16/o v.4 can be connected to a Pro64 digital snake or audio network by adding the ASI A-Net Systems Interface.
Outputs DB25 multipin connectors (2); Tascam analog audio pinout; Impedance balanced output for mic, +4dBu, and +18dBu; differential output for +24dBu
D/A Conversion 48kHz sample rate, 24 bit
Frequency Response 4Hz-22kHz
A-Net Input/Output one EtherCon Category 5 (RJ45 connector)
A-Net Expansion one EtherCon Category 5 (RJ45 connector)
Output Level Settings Four-position switch, per channel pair; +24dBu, +18dBu, +4dBu, and Mic
Channel LED Indicators Signal Present and Clip, per channel
Metering LEDs; green: Signal Present; red: Clip; per channel
Maximum Output Level +24dBu
Output Impedance 226 ohms (+18dBu, +24dBu); 100 ohms (+4dBu and mic)
Freq. Response 4Hz-22kHz +0.2dB/-3dB
THD +N < 0.004%
Bit Error Rate (BER) 10(-12)
Signal to Noise (unweighted) 92dB typical, A/D to D/A; Measured from AN-16/i to AN-16/o v.4 Output Module
Digital Connections A-Net In: 1; A-Net Out: 1; A-Net Expansion: 1; Neutrik EtherCon connectors
A-Net Pro16 A-Net Expansion combines two A-Net streams (32 channels of audio) onto one Cat-5e cable; uses unshielded Cat-5e UTP (or better) cable
Latency <0.620 msec (measured from analog input to analog output)
Power Supply External, DC, universal switching type
Input Voltage 100-240 volts 50/60Hz, 30VA
Output Voltage 24 VDC, 0.5 amp
Plug Size 2 mm
Power 24 VDC, 500mA
Dimensions 19" (482.6 mm) wide x 5.75" (146 mm) deep; 1U high
Weight 6.8 lbs. (3.08 kg)